BN 12-10Z
BN 12-10Z
Downloads
- Actuation from side
- With pre-wired cable
- with bias magnet
- Non-contact principle
- Long life
- Metal enclosure
- Actuating distance up to 60 mm depending on actuating magnet and version
- Design Ø 10.7 mm
- with central mounting
Ordering data
| Product type description |
BN 12-10Z |
| Article number (order number) |
101101263 |
| EAN (European Article Number) |
4030661335315 |
| eCl@ss number, version 12.0 |
27-27-43-02 |
| eCl@ss number, version 11.0 |
27-27-01-05 |
| eCl@ss number, version 9.0 |
27-27-01-05 |
| ETIM number, version 7.0 |
EC002544 |
| ETIM number, version 6.0 |
EC002544 |
General data
| Working principle |
Magnetic drive |
| Housing construction form |
Cylinder, thread |
| Housing material |
Metal film |
| Gross weight |
60 g |
General data - Features
| Suitable for elevators |
Yes |
| bias magnet |
Yes |
| Number of normally open (NO) |
1 |
Mechanical data
| Active area |
lateral |
| Actuating element |
Magnet |
| Mechanical lifetime, minimum |
10,000,000 Operations |
| Actuating speed, maximum |
18 m/s |
| Mounting |
central with threated flange M12 x 1 |
Mechanical data - Switching distances
| Switching distance Sn |
5 mm … 50 mm BP 10 = 5 mm 2 x BP 10 = 17 mm BP 15 = 6 mm 2 x BP 15 = 17 mm 2 x BP 15/2 = 17 mm BP 34 = 15 ... 20 mm BP 20 = 20 mm BP 31 = 20 mm BP 11 = 20 mm BP 12 = 10 ... 30 mm BP 21 = 25 ... 50 mm |
| Note (Switching distance Sn) |
Actuating distance up to 50 mm depending on actuating magnet and version. The specified switching distances are applicable for the actuation of individually mounted components without ferromagnetic influence. A change of the distance, either positive or negative, is possible due to ferromagnetic influences. The mutual interference between multiple actuating magnets must be observed. |
| Note (switching distance) |
All switching distances in accordance EN IEC 60947-5-2 |
| Repeat accuracy R |
0.3 mm |
Mechanical data - Connection technique
| Length of cable |
1 m |
| Termination |
Pre-wired cable |
| Number of cable wires |
2 |
| Wire cross-section |
0.25 mm2 |
| Wire cross-section |
23 AWG |
| Material of the Cable mantle |
PVC |
| Cable type |
LiYY |
Mechanical data - Dimensions
| Diameter of sensor |
10.7 mm |
| Length of sensor |
71 mm |
Ambient conditions
| Degree of protection |
IP67 |
| Ambient temperature |
-25 ... +70 °C |
| Resistance to vibrations |
10 … 55 Hz, amplitude 1 mm |
| Restistance to shock |
30 g / 11 ms |
Electrical data
| Switching voltage, maximum |
200 VAC |
| Switching current, maximum |
1 A |
| Switching capacity, maximum |
30 W |
| Switching capacity, maximum |
30 VA |
| Switching principle |
Reed contacts, Non-contact principle |
| Bounce duration, maximum |
0.2 ms |
| Switching frequency, maximum |
300 Hz |
| Switching element |
Normally open contact (NO) |
Scope of delivery
| Scope of delivery |
Actuator must be ordered separately. |
Accessory
| Recommendation (actuator) |
BP 10 2x BP 10 BP 15 2x BP 15 2x BP 15/2 BP 34 BP 20 BP 31 BP 11 BP 12 BP 21 |
| Recommendation (actuator, lift switchgear) |
BP 10 2 x BP 15/2 2 x BP 15 2 x BP 10 BP 15 BP 34 |
Note
| Note (General) |
The opening and closing functions depend on the direction of actuation, the actuating magnets and the polarity of the actuating magnets. When the switches and actuators come together, the colours must coincide: Red (S) to red (S) and green (N) to green (N). This does not apply to the bistable contact. The switch is to be mounted on iron with a non-magnetic layer of at least 20 mm. |
Language filter
Datasheet
Mounting and wiring instructions
Declaration of conformity (EC)
Info
Download the latest version of Adobe Reader
Product picture (catalogue individual photo)
ID: kbn12f01
| 164.6 kB | .jpg | 352.778 x 528.8140000000001 mm - 1000 x 1499 px - 72 dpi
| 19.8 kB | .png | 73.73100000000001 x 110.772 mm - 209 x 314 px - 72 dpi
| 13.4 kB | .jpg | 82.197 x 123.47200000000001 mm - 233 x 350 px - 72 dpi
| 8.7 kB | .png | 74.083 x 74.083 mm - 210 x 210 px - 72 dpi
| 1.6 MB | .png | 166.55700000000002 x 249.67000000000002 mm - 2000 x 2998 px - 305 dpi
Dimensional drawing basic component
Switch travel diagram
Contact closed
Contact open
Setting range
Latching point
Positive opening path/angleDiagram
Monitoring the interlock to EN ISO 14119
Positive break NC contact
Actuated
Not actuated
Normally-open contact
Normally-closed contact
101060163 BP 15
- thermoplastic enclosure
- N-pole marked green
- S-pole marked red
- Suitable for mounting on ferrous material with a distance of 18 mm
101060165 BP 15/2
- Unenclosed
- Polarity stamped in
- Suitable for mounting on ferrous material with a distance of 18 mm
101057531 BP 10
- Unenclosed
- Colour coding of poles by lables
151057553 BP34
- thermoplastic enclosure
- S-pole marked red
- N-pole marked green
- Suitable for mounting on ferrous material with a distance of 25 mm
Schmersal, Inc., 15 Skyline Drive, NY 10532 Hawthorne
The details and data referred to have been carefully checked. Images may diverge from original. Further technical data can be found in the manual. Technical amendments and errors possible.
Generated at: 2026-04-15, 6:09 a.m.
Recently viewed
SHGV/L01/216+BO
